Hardware Manuals


Gemini - PMX20  

TOP PANEL CONTROLS





CONTROL

ACTION

1 CROSSFADER
Blends Audio signal from left/right assigned channels
2 VOLUME
Adjust the Output Volume of each Channel. The series of leds next to each Volume fader indicate the pre-fader output level of each channel
3 MASTER VU METER
This series of leds indicate the output level of Left/Right stereo channels of the Master Output
4 CUE
Use these buttons to send the pre-fader audio signal of each channel to the Headphones channel for pre-listening
5 FX SEND
If an external Effect generator device is connected at the reap panel to SEND/RETURN sockets, use these buttons to send (and receive) the processed audio signal of each channel from that device
6 FILTER
Apply a High/Low Pass Filter to each channel. When in middle position, no Filter is applied.
7 EQUALIZER
Adjust the 3 Equalizer bands (High/Mid and Low) for each channel.
8 GAIN
Adjust the pre-fader output level of each channel.
9 USB
Use these buttons to select the source of each mixer channel. When disabled/off, the audio signal from the source connected to the respective Input CH (rear panel) wil lbe routed to the mixer channel and the respective VirtualDJ deck will be muted. Enable (led ON), to allow control and audio signal from a VirtualDJ deck.
10 MASTER VOLUME
Adjust the output volume of the Master Output (connection at the rear panel)
9 BOOTH VOLUME
Adjust the output volume of the Booth Output (connection at the rear panel)
12 RETURN
Adjust strength of the signal coming from the Return Input (rear panel)
13 MIC CONTROLS
Adjust the output volume of the Microphone Input (connection at the rear panel), turn on/off the Microphone or enable the TALK OVER to automatically reduce output level when signal is detected from the Microphone Input.
14 CUE/PGM
Blends audio signal from Master Output (when in PGM) and channels that have the CUE enabled (when in CUE) and sends to the Headphones Output (connection at the front panel)
15 CUE LEVEL
Adjust the volume of the Headphones Output (connection at the front panel)
16 BACK
Use this button to set focus to the Folders list of Browser. If focus is on the Folders List, use this button to open/close sub-folders.
When the SAMPLES buttons is pressed, use this button to select the next available Sampler Trigger mode (on/off, hold, stutter and unmute)
17 FWD
Use this button to set focus to the next Browser window/list (Folders, Files, Sideview).
While the SAMPLER button is pressed, use this button to load and select the next available Sampler Bank
18 LOAD
Press to load the selected track from Browser to deck 3,2,1 or 4.
19 TRACK SEARCH
Scrolls though files or folders depending on the selected Browser window.
When focus is on Folders list, push to set focus to the Files/Tracks List.

While the SAMPLER button is pressed, use this encoder to adjust the Sampler Master Volume
20 EFFECT 2 - ON
Use this button to toggle between FX Select and FX Param modes.
21 EFFECT 2 - KNOB
When the FX Select mode is enabled (default mode - EFFECT 1 - ON is off) use this knob to adjust the 2nd Parameter of the selected Effect on Left/Right assigned Deck.
When the FX Param mode is enabled (EFFECT 1 - ON is on) use this knob to select the Effect for the Left/Right assigned Deck
22 EFFECT 1 - ON
Use this button to enable/disable the selected Effect on Left/Right assigned Deck
23 EFFECT 1 - KNOB
Adjust the 1st Parameter of the selected Effect on Left/Right assigned Deck
24 LOOP SIZE
Halve (anti-clockwise) /Double (clockwise) the size of the Loop
25 LOOP ON
Enable/disable an auto-loop of the selected size in beats for the Left/Right assigned deck
26 DECK ASSIGN
Use these buttons to assign a deck as Left/Right. The Effect, Loop and Pads section of the PMX20 will apply their assigned functions to the selected Left/Right deck.
Use the left-side button 1 to assign Deck 1 as Left deck
Use the left-side button 3 to assign Deck 3 as Left deck.
Use the right-side button 2 to assign Deck 2 as Right deck
Use the right-side button 4 to assign Deck 4 as Right deck.
27 CUES
Sets the 8 colored Pads to Hotcues mode.
28 SAMPLES
Sets the 8 colored Pads to Sampler mode.
29 PADS
In Hotcues mode : Use the pads to assign Hotcues 1 to 8 or jump to their stored positions if not assigned. Hold CUES button down and then press a Pad to delete its stored Hotcue.
In Sampler mode : Use the pads to trigger samples 1 to 8 from the selected Sampler Bank. Depending on the selected Trigger mode, you may find useful to stop a playing sample, by holding down the SAMPLES button and pressing the related pad.
30 EFFECT 1 - KNOB
Connect a pair of Headphones to this socket (for pre-listening) using a 1/4" cable/plug
31 CURVE CONTROL
Use this knob to adjust the curve/slop for the Crossfader (smooth when at minimum position, cut/scratch when at maximum)

Pannello Posteriore