Entra:     

Forum: General Discussion

Topic: Setting audio vdj2020 with pioneer DDJ-SZ

Questo argomento è obsoleto e potrebbe contenere informazioni obsolete o errate.

Hello platform, please help me please! If I plug my vdj pro infinity 2020 to the Pioneer DDJ-SZ controller it takes full control of the software but the sound does not come out on the front panel, it only plays in my computer, I do not know how to do it and I still connect the small line jack to the pc to collect the sound, which means that I use 3track on the controller mixer but no preview too .... in short, I was there on the pioneer site to download the DDJ-SZ driver I can only find the DDJ-SZ2 ​​and other drivers with which I tried but the sound does not come ...... please help me ... thank you
 
Inviato Sat 12 Sep 20 @ 12:02 pm
I am currently in front of my pc and the controller to follow your instructions and apply them at the same time .... please give me a follow up
 
I am ok now,i have found the right driver DDJSZ,but now my crossfader doesn't take effect when i move it
 
 
Thankx a lot my master RUNE
 
@RUNE,If only i can have the manual like this for all numarks controler to vdj....once more thank you
 
 
Okay boss...thankx
 
You only get 10 minutes to use the software, right?
 
hello great technicians, please save me it's urgent, I don't understand anything, for more than 4 months already I use vdj 8 2020 pro infinity with pionneer ddj sz, no problem, it's been 3 days I don't understand why when I connect the same computer that I have been using since, when I connect it to the console I start the sound, the sounds of the 2 decks play on a single track on the mixer, but the audio configurations are always the same, please save me , I even tried to uninstall and reinstall the ddj sz driver, and even also all the vdj 8 2020 software, still the same problems, only one volume of the mixer controls the 2 decks, and also I notice that sometimes I have to raise 2 sliders of the volume of the mixer so that the sound of a deck can come out .... here I am seriously in the incomprehensible conplications, ... help me please, please, this very evening I have a service but I'm stuck
 
 
yes yes I have a license, and also the configurations are correct also as I have been using it for months, and also it was your link I had followed to download the ddjsz driver for more than 4 months I want to thank you for your help, just that at home on the sound card side it displays "PIONEER DDJ-SZ (WASAPI)" and it has always been like that for a while since I installed the driver and everything was fine, and so far it is always like that but I don't know what the problem is anymore
 
this is my configuration that I have been using since without any worries Deck 1 ---- PIONEER DDJ-SZ (WASAPI) ---- chan1 & 2 ---- 41.1k 21ms 2o Deck2 ---- PIONEER DDJ-SZ (WASAPI) --- chan 3 & 4 ----- 41.k 21 ms 2o Deck3 --- PIONEER DDJ-SZ (WASAPI) ---- chan 5 & 6 --- Deck 4 --- PIONEER DDJ-SZ (WASAPI) --- there is no chan 7 & 8, so it's on chan 5 & 6 as well.
 
oupsss !!! finally it's good, it's fine For the sound configuration, now my samplers when I press on the pads it play in the base of the samplers but the sound does not come out, since I do not even have modified the sampler folder ... the proof when I disconnect the pionneer ddj sz console, the sound of the samplers comes out in the top of my computer, .... what to do please
 
 


(Vecchi argomenti e forum sono automaticamente chiusi)