Pads

LOOP MODE

Hold MODE button [15] down and then press Pad 1 to set Pads to Loop Roll mode.

Press and hold a Pad down to apply a Loop of a different size in beats. When Pad is released, the track will resume playing from the position it would have been if the Loop was never applied.

KEY

ACTION

SHIFT (SECONDARY) ACTION

P1 PAD1

Applies a Loop Roll of 1/8 beat

Loop In : When not in loop, sets current position as the beginning of the Loop. If in loop, jumps to the beginning of the loop

P2 PAD2

Applies a Loop Roll of 1/4 beat

Loop Out: When not in loop, sets deck in loop, starting from the last Loop In point. When in Loop, exits the Loop

P3 PAD3

Applies a Loop Roll of 1/2 beat

Reloop : When not in loop, jumps to the beginning of the previously triggered loop and sets deck in loop. When in loop, jumps to its beginning

P4 PAD4

Applies a Loop Roll of 1 beat

Records deck to a new Sample

---

FX MODE

Hold MODE button[15] down and then press Pad 2to set Pads to Effects mode.

P1 PAD1

Enables/disables the selected Effect of FX Slot 1

Selects the next available Effect for FX Slot 1

P2 PAD2

Enables/disables the selected Effect of FX Slot 2

Selects the next available Effect for FX Slot 2

P3 PAD3

Enables/disables the selected Effect of FX Slot 3

Selects the next available Effect for FX Slot 3

P4 PAD4

Enables/disables the FX Parameter mode. When enabled (LED on), use the LOOP ENC to adjust the 1st Parameter of all 3 FX Slots. Hold SHIFT down and then use the same LOOP ENC to adjust the 2nd Parameter of all 3 FX Slots

---

SAMPLE MODE

Hold MODE button [15] down and then press Pad 3 to set Pads to Sampler mode.
While Pads are in Sampler mode, hold the MODE button [15] down and use the LOOP ENC to adjust the Master Volume of the Sampler.

KEY

ACTION

SHIFT (SECONDARY) ACTION

P1 PAD1

Triggers Sample 1/5* from the selected Sampler Bank

Selects and loads the previous available Sampler Bank

P2 PAD2

Triggers Sample 2/6* from the selected Sampler Bank

Selects and loads the next available Sampler Bank

P3 PAD3

Triggers Sample 3/7* from the selected Sampler Bank

Sets Sampler Pads to On/Off trigger mode

P4 PAD4

Triggers Sample 4/8* from the selected Sampler Bank

Sets Sampler Pads to Hold trigger mode (play while pressed)

*Note: If the selected Sampler Bank has less than 5 samples, both sides of the Pads will trigger the same samples. If the selected Sampler Bank has more than 4 samples, the left side Pads will trigger Samples 1 to 4 and the right side Pads will trigger Samples 5 to 8.

---

CUE MODE

Hold MODE button [15] down and then press Pad 4 to set Pads to Hotcue mode.

KEY

ACTION

SHIFT (SECONDARY) ACTION

P1 PAD1

Sets current track's position as Hotcue 1 if not set or jumps to it's stored position if set.

Deletes Hotcue 1

P2 PAD2

Sets current track's position as Hotcue 2 if not set or jumps to it's stored position if set.

Deletes Hotcue 2

P3 PAD3

Sets current track's position as Hotcue 3 if not set or jumps to it's stored position if set.

Deletes Hotcue 3

P4 PAD4

Sets current track's position as Hotcue 4 if not set or jumps to it's stored position if set.

Deletes Hotcue 4

---

For further Technical features and specifications, visit
Hercules DJ Control Instinct P8
Product's Page

---

Hardware Integration Department 2018 - ATOMIX PRODUCTIONS


Reproduction of this manual in full or in part without written permission from Atomix Productions is prohibited.