Hardware Manuals


Reloop - Elite  

Setup Avanzato


CUSTOM MIDI MAPPING


All the elements (faders, knobs, buttons, rotaries etc) of the Reloop Elite are sending MIDI messages to the connected computer.

Most of the mixer elements are assigned to a VirtualDJ mixer action and the "fake mixer" mode is enabled since the audio mixing is done by the Reloop Elite and not the internal mixer of VirtualDJ. This means that whatever adjustments are made on the internal mixer of VirtualDJ (e.g. moving a Volume fader from the VirtualDJ GUI) will not affect the audio routing or output.

Some other elements offered in the Key list (Controllers tab of VirtualDJ Settings) can be assigned to any VirtualDJ action, but keep in mind that the Hardware operation of some of those will be still executed.
This means that if for example you wish to assign an element from the Mic section to a VirtualDJ action, the respective Microphone operation will be executed by the Reloop Elite if a Microphone is connected to a MIC input.

Mixer UTILITIES


The Reloop Elite is offering a Utilities menu with a few options. Refer to the Reloop Elite Operation Manual for further details

How to access the Utilities menu.
  • Hold both SHIFT and BACK buttons for more than 3 seconds, until the LCD displays "FADER SETTINGS".
  • Use the BROWSE rotary to navigate through the available settings.
  • Push the BROWSE rotary to select a setting and adjust its value.
  • Go back or/and Exit the Utilities menu using the BACK button . The unit will exit Utilities automatically if no selection/adjustment is made within a few seconds.



Timecode (DVS)


VirtualDJ is offering DVS (Digital Vinyl System) support for the Reloop Elite. A Pro Infinity or Pro subscription license is required. http://www.virtualdj.com/buy/index.html

Both Mixer Channels can accept PHONO (Timecode Vinyls) and LINE (Timecode CDs) Inputs
  • Depending on the type of DVS media CD/Vinyl, connect your Timecode devices at the LINE/PHONO sockets respectively at the rear panel of the Reloop Elite Inputs and make sure the SOURCE switchers at the top panel are set to USB A/B position.

  • Use the Utilities of the Elite to set the respective USB Channels to PHONO or LINE depending on the connected DVS device.
    [list]
  • Open the Utilities by holding both SHIFT and BACK buttons for more than 3 seconds, until the LCD displays "FADER SETTINGS".
  • Use the BROWSE encoder to navigate to the setting USB OUT ROUTING
  • Push the BROWSE encoder. The right-side LCD will display and blink DECK 1 and its selected value below that.
  • Push the BROWSE encoder to change the setting. Use the BROWSE encoder and select CD or PHONO depending the DVS type you have connected to this Deck.
  • Repeat the previous 2 steps for DECK B.
  • Exit the Utilities.

The USB routing is saved across sessions and power-cycling.

  • Open the AUDIO tab of VirtualDJ Settings and click on the TIMECODE button for VirtualDJ to add 2 Timecode inputs


    Reloop ELITE– Audio Setup Timecode Inputs


  • Click to APPLY.

  • Press PLAY on your timecode CD and/or Vinyl device and VirtualDJ will automatically detect your Timecode type and make the appropriate adjustments for best performance.

  • Open the TIMECODE tab of the VirtualDJ Settings and choose the CALIBRATE button if for any reason the signal is not detected (possibly due to reversed phase connections).

  • Click on the ON buttons from the TIMECODE panels of the Default Skin to enable the Timecode control to any Deck
    [/list]

    Recording


    The Reloop Elite audio interface is offering a dedicated REC USB stereo output channel, to record your Main Mix along with Microphone/Aux Inputs and it's pre-defined in VirtualDJ audio setup.

    However, the REC USB channel (set as REC OUT by default), could be set differently, so make sure it's set as such.
    • Open the Utilities by holding both SHIFT and BACK buttons for more than 3 seconds, until the LCD displays "FADER SETTINGS".
    • Navigate to the setting USB OUT ROUTING
    • Push the BROWSE encoder. The right-side LCD will display and blink DECK 1 and its selected value below that.
    • Use the BROWSE encoder to navigate to the REC setting.
    • Push the BROWSE encoder to change the setting.
    • Use the BROWSE encoder and select the REC OUT
    • Push the BROWSE encoder to confirm.
    • Exit the Utilities.


    To record your mix, simply open the MASTER center panel of the VirtualDJ GUI and click to the REC button (or BCAST for broadcasting).




    For further Technical features and specifications, visit

    Reloop ELITE
    Product's Page




    Hardware Integration Department
    2019 - ATOMIX PRODUCTIONS



    Reproduction of this manual in full or in part without written permission from Atomix Productions is prohibited.